P/N134432200(0405)
This Owner's Guide provides general
operatinginstructionsforyourdryer. It
alsocontainsinformationaboutfeatures
for several other models. Your dryer
may not have every feature included.
Protect Children
Do not allow children to play on or in the dryer. Close supervision of
children is necessary when the dryer is used near children. As children grow, teach
them the proper, safe use of all appliances.
Use the dryer only as instructed in this
Owner's Guide and the Operating
Instructions card included with your
dryer.
Destroy the carton, plastic bag and other packing materials after the
dryer is unpacked. Children might use them for play. Cartons covered with rugs,
bedspreads or plastic sheets can become airtight chambers.
Keep laundry products out of children's reach. To prevent personal
injury, observe all warnings on product labels.
Avoid fire hazard or
electricalshock. Donotuseanadaptor
plug or extension cord or remove
groundingprongfromelectricalpower
cord. Failuretofollowthiswarningcan
cause serious injury, fire or death.
Before the dryer is removed from service or discarded, remove the
dryer door to prevent accidental entrapment.
Failure to comply with these warnings could result in serious personal injuries.
Prevent Injury
ELECTRIC DRYERS:
To prevent shock hazard and assure stability during operation, the
dryer must be installed and electrically grounded by a qualified service person in
accordance with local codes. Installation instructions are packed in the dryer for the
installer's reference. Refer to INSTALLATION INSTRUCTIONS for detailed grounding
procedures. If the dryer is moved to a new location, have it checked and reinstalled
by a qualified service person.
14-30R
DRYER
FUSED30AMP
120/240 V OR
120/208 V
WALL
RECEPTACLE
DRYER
SERVICECORD
To prevent personal injury or damage to the dryer, the electrical
power cord of a gas dryer must be plugged into a properly grounded and polarized
3-prong outlet. The third grounding prong must never be removed. Never
ground the dryer to a gas pipe. Do not use an extension cord or an adaptor
plug.
CORRECT
Use this way ONLY
GAS DRYERS:
ALWAYS disconnect the dryer from the electrical supply before
attempting any service or cleaning. Failure to do so can result in electrical shock or
injury.
Grounding type
wall receptacle
Do not under
any circumstances
cut, remove,
Do not use any type spray cleanser when cleaning dryer interior.
Hazardous fumes or electrical shock could occur.
or bypass
the grounding prong
from this plug.
To prevent injury, do not reach into the dryer if the drum is moving.
Wait until the dryer has stopped completely before reaching into the drum.
Power supply
cord with 3-prong
grounding plug
To prevent injury and damage to the dryer:
•
All repairs and servicing must be performed by an authorized servicer
unless specifically recommended in this Owner's Guide. Use only authorized
factoryparts.
Do not tamper with controls.
Do not install or store the dryer where it will be exposed to the weather.
CORRECT
Use this way ONLY
•
•
A thermal limiter switch automatically turns off the motor in the unlikely event
ofanoverheatedsituation(electricdryersonly).Aservicetechnicianmustreplacethe
thermal limiter switch after correcting the fault.
Note: The instructions appearing in this
Owner's Guide are not meant to cover
every possible condition and situation
that may occur. Common sense and
cautionmustbepracticedwheninstalling,
operatingandmaintaininganyappliance.
Failure to comply with these warnings could result in serious personal injuries.
SAVE THESE INSTRUCTIONS
3
• Follow the guidelines below for preparing the load for drying.
Drying Procedures
• Read the Operating Instructions card for operating your specific model.
• Always read and follow fabric care labels and laundry product labels.
To reduce the risk of fire, electrical shock, or injury to persons, read
Important Safety Instructions, pages 2-3, before operating this dryer.
1. Prepare items for drying.
•
Dry items of similar fabric, weight and construction in the same load.
•
Separate dark items from light-colored items. Separate items that shed lint
from those that attract lint. If an item sheds lint, turn it inside out.
•
Besurebuckles,buttonsandtrimareheatproofandwon'tdamagethedrum
finish.Closezippers,fastenhooksandVelcro®-likefasteners.Tiestringsand
sashes to prevent snagging and tangling.
•
•
If possible, turn pockets inside out for even drying.
Check for stains which may not have been removed in washing. Dryer heat
may permanently set some stains. Repeat stain removal process before
drying.
Follow fabric care label instructions.
•
Place small items in a mesh bag to prevent tangling and for easy removal.
2. Check that lint screen is clean and in place.
3. Load the dryer.
•
•
•
•
•
Theaverageloadwillfillthedrum1/3to1/2full.Itemsneedroomtotumble
freely for even drying and less wrinkling. Do not overload dryer.
Whendryinglargeitems,dryonly2or3atatime.Fillouttheloadwithsmall
and medium sized items.
For delicate or very small loads, add 2 lint-free towels for better drying, less
wrinkling, and to prevent grease stains caused by fabric softener sheets.
Donotoverdryitems.Overdryingcancausewrinkling,shrinkage,harshness,
and a build-up of static electricity, which can produce more lint.
Place small items in a mesh bag.
If desired, add a dryer fabric softener sheet.
4. Close the dryer door and set dryer controls (some models).
See Operating Instructions card for your specific model controls.
5. Turn cycle selector clockwise to the desired setting.
6. Start the dryer.
•
PushStartButtonfor2secondsorturntheSTARTknobclockwisetoON,hold
for 1-2 seconds and release.
•
Toaddorremoveitemswhenthedryerisrunning,openthedoor.Thedryer
will always stop when the door is opened. Allow the drum to come to a
complete stop before reaching inside.
•
•
To restart dryer, close the door then push the Start Button for 2 seconds or
turn the START knob clockwise to ON, hold for 1-2 seconds and release.
The dryer will not start if the cycle selector is in the OFF position.
7. When the cycle ends, remove items immediately and hang
Fill dryer drum 1/3 to 1/2 full.
or fold. If load is removed before the cycle ends, turn cycle selector to OFF.
4
Cycle Signal Control (some models)
Features
When the Cycle Signal Control is ON, a signal will sound at the end of each cycle
andduringthePressSaversetting(somemodels).Thevolumeisadjustableonsome
models.
Drum Light (some models)
Adrumlightwillcomeonwheneverthedoorisopenedtoilluminatethedryerdrum
during loading and unloading. Closing the door turns off the light.
Reversible Dryer Door
Your dryer is equipped with a reversible door. The door can be hinged on the right
or left side. Refer to the INSTALLATION INSTRUCTIONS for directions on changing
the door.
Drying Rack (some models)
Use the drying rack to dry items which should not be tumble dried.
1. Open the dryer door and remove the lint screen.
2. Insert drying rack into the dryer drum. Place the front bar under the lip of the
lint screen opening.
3. Place items to be dried on top of the rack. Weight should not exceed 10 lbs.
Leavespacebetweenitems, butdonotletitemshangoverthesidesorthrough
the grids. Do not tumble other items when using the drying rack.
4. Selectatimeddrysettingbestsuitedforitemsbeingdried.UseonlytheAirFluff
(noheat)temperaturesettingforitemscontainingplastic,foamrubber,rubber-
like materials, feathers or down.
5. When items are dry, remove the rack and replace the lint screen. If lint screen
is not in place, tumbling items could enter the exhaust system and cause
damage to the dryer.
Place the front bar under
the lip of the lint screen opening.
Common Drying Problems
Many drying problems involve poor cleaning results, poor soil and stain removal, residues of lint and scum, and fabric damage.
For satisfactory drying results, follow these suggestions provided by The Soap and Detergent Association.
PREVENTIVE MEASURES
• Add a few bath towels to small loads for
proper tumbling.
PROBLEM
Greasy, oily
stains
POSSIBLE CAUSES SOLUTIONS
• Fabric softener sheet.
• Rub fabric softener stains with bar soap.
Rinse and rewash.
• Some "silk-like" fabrics should be air dried.
• Use proper drying temperature.
• Place fabric softener sheet on top of load
before starting the dryer.
Lint
• Do not overload dryer.
• Use fabric softener in washer or dryer to
reduce static electricity.
• Remove items when they are slightly damp
to avoid overdrying.
• Check that lint screen is clean and in place.
• Overloading.
• Overdrying causes static
electricity.
• Lint screen not clean
when cycle began.
• Lint is attached to "pills."
• Reduce load size and rewash using liquid
fabric softener in the final rinse.
• Or, add a fabric softener sheet and
tumble without heat.
• Use lint brush or roller to remove lint.
Pilling
• Use a lint brush or shaver to remove pills.
• Use fabric softener to lubricate fibers.
• When ironing, use spray starch or fabric
finish on collars and cuffs.
• Pilling is normal with
synthetic and permanent
press fabrics. This is due
to abrasion from normal
wear.
(Fibers break
off, ball up and
cling to fabric.)
• Turn items inside out to reduce abrasion.
Shrinking
• Irreversible condition.
• Follow fabric care label directions.
• If shrinking is a concern, check load often.
• Remove items while slightly damp and
hang or lay flat to complete drying.
• Block knits into shape.
• Overdrying.
Wrinkling
• Reduce load size and tumble at medium
or low heat for 5-10 minutes.
• Remove items immediately. Hang or fold.
• Do not overload dryer.
• Remove items as soon as cycle ends.
• Overloading.
• Leaving items in dryer
after cycle ends.
5
To reduce risk of fire or serious injury to persons or property, comply
with the basic warnings listed in Important Safety Instructions, pages 2-3, and
those listed below.
Care and Cleaning
•
•
Before cleaning the dryer interior, unplug the electrical power cord to avoid
electrical shock hazards.
Do not use any type spray cleanser when cleaning dryer interior. Hazardous
fumes or electrical shock could occur.
Inside
•
Cleanthelintscreenaftereveryload.Lintbuild-upinthescreenrestrictsairflow,
whichcauseslongerdryingtimes.Thescreenislocatedatthebottomofthedoor
opening.Removebypullingstraightup.Removethelintandreplacethescreen.
•
Occasionallyawaxybuild-upmayformonthelintscreenfromusingdryer-added
fabric softener sheets. To remove this build-up, wash the lint screen in warm,
soapy water. Dry thoroughly and replace. Do not operate the dryer without the
lint screen in place.
Clean lint screen after every load.
•
•
Ifthedryerdrumbecomesstainedfromnoncolorfastfabrics,cleanthedrumwith
a damp cloth and a mild liquid household cleanser. Remove cleanser residue
before drying the next load.
Every 18 months an authorized servicer should clean the dryer cabinet interior
and exhaust duct. These areas can collect lint and dust over time. An excessive
amountoflintbuild-upcouldresultininefficientdryingandpossiblefirehazard.
Outside
•
•
•
•
Clean the cabinet with mild soap and water. Never use harsh, gritty or
abrasivecleansers.
If the cabinet becomes stained, clean with diluted chlorine bleach [1/2 cup
(120 ml) in 1 quart (.95 liter) water]. Rinse several times with clear water.
Removeglueresiduefromtapeorlabelswithamixtureofwarmwaterandmild
detergent. Or, touch residue with the sticky side of the tape or label.
Do not store or place laundry products
on top of dryer at any time. They can
damage the finish or controls.
Before moving the dryer, place a strip of cardboard or thin fiberboard under
the front leveling legs to prevent damage to floor.
6
Before calling for service, review this list. It may save both time and expense. The list includes
common occurrences that are not the result of defective workmanship or materials in this dryer.
Avoid Service
Checklist
OCCURRENCE
POSSIBLE CAUSE
SOLUTION
Electrical power cord is not securely plugged
in or plug may be loose.
Make sure the plug fits tightly in wall outlet.
Dryer does not start.
House fuse blown or circuit breaker tripped.
Reset circuit breaker or replace fuse.
Make sure electrical line is not overloaded and the dryer is on
a separate circuit.
Thermal limiter tripped.
Call authorized service person for replacement.
Replace fuse.
There are 2 house fuses in the dryer circuit. If
1 of the 2 fuses is blown, the drum may turn
but the heater will not operate.
Dryer runs but won't heat.
Gas supply valve is not open (gas models).
Check to make sure supply valve is open. See INSTALLATION
INSTRUCTIONS for procedure.
Dryer does not have anough air supply to
support the burner flame (gas models).
See INSTALLATION INSTRUCTIONS.
LP gas supply tank is empty or there has been
a utility interruption of natural gas (gas
models).
Refill or replace tank.
Dryer should heat when utility service is restored.
Lint screen is clogged with lint.
Makesurealllinthasbeenremovedfromthedryerlintscreen
before starting each cycle.
Drying cycle takes too long,
outsideofthedryerfeelstoo
hot or smells hot.
Exhaust duct requirements have not been
met.
Exhaust duct must be at least 4 inches in diameter and made
of rigid or flexible metal.
When in place, the duct must have no more than two 90°
bends and must not exceed length listed in INSTALLATION
INSTRUCTIONS.
Electricdryerisconnectedtoa208voltcircuit.
Drying procedures have not been followed.
Drying time will be 20% longer than drying on a 240 volt
circuit.
See Drying Procedures, page 4.
Outside exhaust hood or exhaust duct may
be clogged or restricted.
Clean out any obstruction.
High humidity.
Use a dehumidifier near the dryer.
Dryer is overloaded.
Do not overload. See Drying Procedures, page 4.
Remove items as soon as cycle ends.
See Drying Procedures, page 4.
Excessive wrinkling.
Items left in dryer too long.
Insufficient sorting of items.
Drying temperature too high.
Follow fabric care label instructions.
Foreign objects such as coins, pins, clips or
buttons are inside the dryer.
Always remove foreign objects from pockets before
laundering. Remove objects from drum and restart dryer.
Scratchingorchippingofthe
drumfinish.
Permanently attached items such as belt
buckles, zippers and fasteners may be hitting
the inside of the drum.
It may be necessary to baste a scrap of material securely
around ornaments before drying to prevent scratching and
damage to the dryer.
Drumdamagecausedbyforeignobjectsorpermanently
attached items is not covered by the warranty.
7
|